Difference between revisions of "Howto Hardware Factory Reset"

From berofix - professional SIP gateway
Jump to: navigation, search
 
Line 7: Line 7:
 
{|
 
{|
 
|[[Image:Bf_HWReset1.png]]
 
|[[Image:Bf_HWReset1.png]]
 +
 
|[[Image:PCM_Hardware.png]]
 
|[[Image:PCM_Hardware.png]]
 
|-
 
|-
Line 14: Line 15:
 
*4. In case of a Box Power up the device or in case of a card plug the card in your computer and power up the device.
 
*4. In case of a Box Power up the device or in case of a card plug the card in your computer and power up the device.
 
*5. After you power up the device the berofix should be reachable again with the default IP address 10.0.0.2. or a new IP-address. Open your Browser with the address and wait until you get a response from the berofix (this could take a couple of minutes. see picture below).
 
*5. After you power up the device the berofix should be reachable again with the default IP address 10.0.0.2. or a new IP-address. Open your Browser with the address and wait until you get a response from the berofix (this could take a couple of minutes. see picture below).
[[Image:Bf_HWReset2.png]]
+
 
*6. Upload a new Firmware (see picture above).
+
[[Image:Hardreset 1.PNG]]
 +
 
 +
*6. Press the Firmware-Update button (see picture above).
 
*7. Install the new Firmware (see picture below).
 
*7. Install the new Firmware (see picture below).
[[Image:Bf_HWReset3.png]]
+
 
*7. Power Down the device and remove the Jumper.
+
[[Image:Hardreset 2.PNG]]
*8. Power Up the device. The device is now Ready with factory defaults.
+
 
 +
*8. Power Down the device and remove the Jumper.
 +
*9. Power Up the device. The device is now Ready with factory defaults.

Latest revision as of 15:10, 9 June 2016

This Howto describes how to do a factory reset on a berofix device. This could be useful in case of a lost password or in any case where you lost the connection to the berofix device. This Feature works only with Firmware Version > 1.12 and FPGA image Version >= 3. The Hardware Factory Reset deletes all data on the berofix device incl. the firmware and restores the default values. There are 8 steps howto initiate the Hardware Factory Reset.

  • 1. Power off the card/device.
  • 2. In case of a card remove the card from your computer. In case of a Box check if you can access the PCM connector on the rear from the outside, otherwise open the box.
  • 3. Card:Short the two pins horizontal with a jumper ( the yellow marked rectangle see Picture below). Box: Short the two pins vertically with a jumper (the yellow marked rectangle see Picture below)
Bf HWReset1.png PCM Hardware.png


  • 4. In case of a Box Power up the device or in case of a card plug the card in your computer and power up the device.
  • 5. After you power up the device the berofix should be reachable again with the default IP address 10.0.0.2. or a new IP-address. Open your Browser with the address and wait until you get a response from the berofix (this could take a couple of minutes. see picture below).

Hardreset 1.PNG

  • 6. Press the Firmware-Update button (see picture above).
  • 7. Install the new Firmware (see picture below).

Hardreset 2.PNG

  • 8. Power Down the device and remove the Jumper.
  • 9. Power Up the device. The device is now Ready with factory defaults.